Skip to main content
All CollectionsManuals
Manual: Valeo
Manual: Valeo
Gina ter Heide avatar
Written by Gina ter Heide
Updated over 3 months ago

Configuration Requirements
● Configuration package E-Flux by Road
Contains: EVSE ID, configuration manual for the installer and
registration manual for the owner of the charging station
● Valeo Ineez Password labels included in the box with the EV charging
station (figure 1)
● Configuration device: laptop

Follow the steps:

Step 1: Power the EV charging station following the video tutorial

Step 2: Activate the Hotspot : please wait until the end of the initialization phase, when the
is in a fixed green state. Now activate the Hotspot of the EV charging station by pressing 3 seconds on the touch button located under the LED (Figure 2).
After 3sec, lift your finger and wait for another 10 sec. When Wifi hotspot is open you have this sequence of the led


​Please make sure to keep your finger pressed for 3 seconds only, beyond this timing the expected behavior of the charging station is to force the start of a charging session.

Step 3: Connect your laptop to the Hotspot on your Laptop check the available networks and connect to the Hotspot Valeo_XXXXX. Enter the Password 1 displayed on the label to connect to the Hotspot.

Step 4: Open the WebUi interface to access the settings Once your Laptop is successfully connected to the hotspot, open a new page in your browser to launch the WebUi interface by entering the following Url : http://10.0.0.1 Your browser may alert you that the connection is not secure and will ask you permission to continue to the site. Click continue to site

Step 5: Login to the WebUi interface.

Enter the standard user name: ineez_user

Key in the specific Password 2 displayed on the label.

At your first Login you will be asked to select a new password, it is recommended to apply a NEW password. Please keep it saved and well secured. You also have the option to use the same password Password 2 and to save.

Step 6: Activate OCPP:
In the Menu “Configuration” you may now activate the OCPP connection
In Config Type: protocol drop down menu, please select : OCPP

  • In the new dedicated field, please enter the e-Flux OCPP server URL:
    ​ws://ocpp.e-flux.nl/1.6/e-flux/
    Please make sure to add the “/” character at the end of the URL address.

  • Enter ChargePoint ID, then save.

  • A pop up window will appear, click on “Restart the services” to apply the changes

After applying the changes, the LED status will change from Green alternating with Yellow, to Red alternating with Yellow. The Red light indicates that the Charging station is not connected to the backend yet.

Step 7/1: Connect the charging station to the internet using “Wi-Fi Client”

Activate the Client Wi-Fi and select the Wi-Fi network you wish to connect to.

Fill in the password of the Wi-Fi network, save and restart the services.

Step 8/1: Once connected to the Wi-Fi you will lose your connection to the EV charging station via WebUi. Please reactivate the Hotspot following Step 2 explained above.

Once you reconnect to the Hotspot you will be notified when the changes have been applied and the EV charging station will be confirmed as successfully connected to the designated Client Wi-Fi. The installation is completed and the EV charging station should now be visible in the backend platform

Step 7/2: Using e-Flux by Road dedicated SIM Card In the setting, instead of activating the Client Wi-Fi, activate the LTE connection. You will be required to enter the following data:

APN Name : m2m.services

You can leave the Username and password empty, since the network of our simcard is open.

Step 8/2: Save and Restart the services to apply the changes.
if the charger has a successful connection to the backend, the LED status will switch from Red to
Green.

If you are the installer of the charging station, go to Step 9. If you are the owner of the charging station, go to step 10.

Step 9: Complete the following steps to activate the station on the E-Flux by Road platform:

  1. Login to your Field Service Account or create a Field Service Account via www.e-flux.io/installer-signup*.

  2. Go to “Setup New EVSE” in the menu on the left and enter the serial number or OCPP ID of the station.

  3. Click on “Setup charging station”.

  4. Click on Upload Configuration, then click Next.

  5. Choose and define the connector type, and choose “Save Connector Configuration”.

  6. The charging station is now activated and ready to be registered by the owner!

*A Field Service Account is for installers only and will be used as a point of contact for technical tickets.

Step 10: Complete the following steps to register the station on the E-Flux by Road platform:

  1. Ask your installer to complete Step 9 to finish the configuration of your charger, or call E-Flux by Road to finish the configuration.

  2. Create an E-Flux by Road account by going to www.e-flux.io/signup.

    • Is this charging station facilitated by your employer? Check your email for the invitation.

  3. Follow the steps to add the location and register your charging station.

  4. Put the sticker with the QR code on the charging station so it’s easier to identify the station if you need support.

  5. The charging station is now registered and ready to be used!

The charging station is now connected to the E-Flux by Road platform!

Did this answer your question?