Skip to main content
All CollectionsManuals
Manual: IES Synergy KEYWATT
Manual: IES Synergy KEYWATT

On this page you will find the steps to connect the IES Synergy KEYWATT charger to the E-Flux by Road platform.

Jochem Boot avatar
Written by Jochem Boot
Updated over 2 months ago

Configuration Requirements

  • Configuration package E-Flux by Road

    • Contains: Sim card (optional), EVSE ID, configuration manual for the installer and registration manual for the owner of the charging station

  • User Manual IES Synergy

  • InTools-QuickGuide IES Synergy

  • Configuration device: laptop

  • Ethernet cable

Follow the steps

Step 1: Determine the OCPP version of the charger by clicking on the information button on the display. If the software is not on version V021, contact IES support for an upgrade.

Step 2: Connect your PC to the OCPP card of the charger. You can connect the ethernet cable to one of the two ports on the OCPP card (see picture below).

Note: eventually the web interface of the charger can be accessed by entering the unique IP address of the connected location:

  • Location 1: 192.168.111.50 :8088

  • Location 2: 192.168.254.50 :8088

Step 3: Change the network settings of your PC by navigating to Control Panel Home → Network and Internet → Ethernet → Properties → Protocol Internet version4 (TCP/IPv4). Dependent on the location the ethernet cable is connected to, you may enter the IP address as shown in the picture below:

  • Location 1: 192.168.111.100

  • Location 2: 192.168.254.100

Step 4: After configuring the right network settings on your PC, enter the IP-address of the location in your preferred web browser:

Step 5: Once the web interface has opened, you can login to the program with one of the following passwords:

  • OPERATOR: iamoperator

  • INSTALLER: iaminstaller

  • PROVIDER: iamadmin

Step 6: Select the Connectivity Setup once you’re logged into the InTools interface and start the configuration.

Step 7: Enter the following values in the Backend settings to connect the charger to the E-Flux by Road backend:

  • Protocol Type: JSON

  • Endpoint (Identification address): ws://ocpp.e-flux.nl/1.6/e-flux

  • Port Listened: 8080

  • Charger Identifier: ‘Enter the unique serial number of the charger’

  • Authorize When Offline Full: false

Step 8: Configure the Communication settings according to the network method used to setup the connection:

  • Modem (SIM):

    • APN: m2m.services

    • APN Username: ‘Leave empty’

    • APN Password: ‘Leave empty’

Note: The APN settings shown above are only applicable to the E-Flux by Road SIM card.

  • Ethernet:

    • Use DHCP to automatically assign an IP-address to the charger, or use Static IP to assign the IP-address manually.

Step 9: Continue to the Summary to check the changes and proceed to the Validation menu to save the configuration.

Note: After saving the configuration, the charger will reboot and connect to the E-Flux by Road backend, assuming the backend and network settings are configured correctly.

If you are the installer of the charging station, go to Step 10. If you are the owner of the charging station, go to step 11.

Step 10: Complete the following steps to activate the station on the E-Flux by Road platform:

  1. Login to your Field Service Account or create a Field Service Account via www.e-flux.io/installer-signup*.

  2. Go to “Setup New EVSE” in the menu on the left and enter the serial number or OCPP ID of the station.

  3. Click on “Setup charging station”.

  4. Click on Upload Configuration, then click Next.

  5. Choose and define the connector type, and choose “Save Connector Configuration”.

  6. The charging station is now activated and ready to be registered by the owner!

*A Field Service Account is for installers only and will be used as a point of contact for technical tickets.

Step 11: Complete the following steps to register the station on the E-Flux by Road platform:

  1. Ask your installer to complete Step 10 to finish the configuration of your charger, or call E-Flux by Road to finish the configuration.

  2. Create an E-Flux by Road account by going to www.e-flux.io/signup.

    • Is this charging station facilitated by your employer? Check your email for the invitation.

  3. Follow the steps to add the location and register your charging station.

  4. Put the sticker with the QR code on the charging station so it’s easier to identify the station if you need support.

  5. The charging station is now registered and ready to be used!

The charging station is now connected to the E-Flux by Road platform!


​

Did this answer your question?